Brodit ProClipTM Mounting Bracket
ProClip is a dashboard mounting bracket for installation of holders, mounting adapters and other accessories. Keep your communication devices attached to the dashboard in a secure and convenient way - always within easy reach!
The ProClip is a mounting bracket for the vehicle´s dashboard. Onto the Proclip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient - always within easy reach. The ProClip is available for most vehicles - trucks as well as left-hand drive vehicles.The ProClip is car specific and easy to install. There are ProClips to suit various positions on the dashboard or console, giving you options for positioning and making several different installations in the vehicle. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the vehicle. Made in black ABS plastic. Comes with detailed instructions.
Does Not Damage the Interior
The interior of the vehicle will not be damaged as no drilling holes is required and you do not need to dismantle the dashboard.
Many Alternatives
The ProClip has a firm fit. There are ProClips to suit various positions on the dashboard or console, giving you options for positioning and making several different installations in the vehicle.
Safer Driving
With your equipment attached to the ProClip, it is always within easy reach. Our goal is to provide you with convenient products and solutions, to give you a safer driving environment while driving and operating your equipment.
Saves Time
The ProClip saves you time. Installation is easy, with no special tools required. Detailed instructions with pictures are included.
Each bracket has been specially designed for each car and has a specially designated place for fitting. Full installation instructions are supplied with the bracket. The bracket will fit in a gap or seam on the cars dashboard. The phone car kit or other accessory cradle is then attached to the no holes ProClip mounting bracket.
RIGHT MOUNT
CENTRE MOUNT
*ANGLED MOUNT
*angled mount recommended for mobile phone hands free kit cradle or holder
CONSOLE MOUNT
Please specify your vehicle make, model and ProClip options at the time of order.
FREE SHIPPING ON THIS ITEM
Installation Procedure
The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the vehicle. See some example fitting instructions below.
Volvo C70 Centre Mount
1. Peel off both adhesive tape covers on the ProClip. Choose location for the ProClip within the range of the width of the air vent. Place the ProClip over the air vent at the selected position. Press the thin end of the two enclosed gap openers into the gap, one on each side of the ProClip, between the padded part of the dashboard and the center console panel to widen the gap.
2. Press the thin end of the lower part of the ProClip all the way into the gap between the gap openers. Pull out the gap openers.
3. Press the grooved edge on the upper part of the ProClip into the gap between the air vent frame and the padded dashboard. Press until you see or hear/feel it snaps into place. (Note: if the gap is very tight, press the thin end of the two enclosed gap openers into the gap, one on each side of the ProClip, to widen the gap. Then press the ProClip into the gap)
4. The ProClip is in place
BMW X3 Centre Mount
1. Press the thin end of the enclosed gap opener into the gap between the frame surrounding the air vent and the frame surrounding the compartment, in order to widen the gap. Peel off the adhesive tape covers on the ProClip. Press the angled edge on the upper part of the ProClip into the gap next to the gap opener. Pull out the gap opener.
2. Press the gap opener into the gap between the frame surrounding the air vent and the frame surrounding the control panel. Press the angled edge in the lower part of the ProClip into the gap next to the gap opener. Pull out the gap opener.
3. Press downwards on the upper part of the ProClip and upwards on the lower part of the ProClip so both ends go all the way into the gaps.
4. The ProClip is in place.
VW Passat Angled Mount
1. Press the smaller one of the enclosed gap openers into the gap between the control panel and the surrounding frame, to widen the gap. Press in into the gap as high as possible, as shown in the picture. Press the other gap opener into the gap in the same about 10 cm below the first gap opener. Peel off the adhesive tape covers on the ProClip.
2. Place the ProClip by the gap between the gap openers. Press the upper part of the ProClip upwards, into the gap between the dashboard and the frame surrounding the control panel.
3. Press the ProClip into the gap between the gap openers. Press forwards on the ProClip so it goes all the way into the gap. Pull out the gap openers.
4. The ProClip is in place.
VW Passat Console Mount
1. Hook the long lower part of the ProClip under the edge of the console.
2. Pull the ProClip upwards. Hook the upper part of the ProClip over the edge of the console.
3 and 4. The ProClip is in place.
